Clean roof runoff · Homes and extensions
Soakaway design in Ireland: sizing, tests and planning
A soakaway stores rainwater underground while it infiltrates into the surrounding soil. Its size depends on the roof draining to it, local rainfall, measured infiltration and the storage available within the chosen material. This guide explains the inputs and checks used by the free Soakaway calculator.
By Soakaway · Updated 30 October 2026
Start free soakaway sizing →Is this the right calculator for my project?
This tool is for rectangular infiltration soakaways receiving clean runoff from impermeable roofs in Ireland, including domestic extensions and one-off houses. It uses the published BRE Digest 365 volume-balance approach with Irish rainfall data.
It does not design septic-tank drainage, wastewater percolation areas, highway drainage or systems for contaminated runoff. A wastewater percolation test is not a substitute for the roof-water infiltration information required here. A soakaway also needs suitable ground conditions; a calculated storage volume alone does not prove the site is suitable.
What do I need to size a soakaway?
- Project location and connected roof area. Enter the roof area that will drain to this device. The location is used to obtain rainfall depths.
- Site infiltration information. Enter a measured rate in metres per second from a suitable test report, or supply the three trial-pit repeats requested by the calculator. Check units carefully.
- Fill material and usable depth. Choose clean stone, geocellular crates or a specified void content. Storage depth below the incoming pipe is different from the total excavation depth.
- Project design settings. Check the return period, climate allowance and infiltration safety factor against the requirements for your project.
- Available space. Optionally enter garden dimensions to screen the proposed excavation against the tool’s assumed clearances. Real obstacles, neighbouring foundations, services and access still need checking.
Start with the free soakaway sizing calculator. The results let you adjust dimensions and review storage, drainage time and any unconfirmed site checks.
Do I need an infiltration test?
A measured infiltration rate is needed to assess how readily water can leave the soakaway. A description such as “clay” or “sandy soil” does not provide a measured design rate. The calculator accepts either a rate from a report or the dimensions, maximum water depth and 75%–25% timing information for three repeats of a rectangular trial pit.
For an early estimate, “Haven’t done a percolation test” uses an assumed rate of 1e-7 m/s. It is deliberately conservative and preliminary. It cannot establish ground suitability or replace testing before a final drainage design is agreed.
How does the BRE 365 calculation work?
The calculator compares rainfall inflow with potential infiltration outflow over the returned storm durations. It finds the largest required storage volume, then compares that with the storage provided by the device’s dimensions and void fraction. A separate check considers how long half the full provided storage takes to drain.
The default settings are 100-year rainfall, a 20% climate allowance and an infiltration safety factor of 2. These are product assumptions, not a statement that every local authority or site requires the same settings. The calculation method and references explain the trial-pit calculation, sidewall outflow area, duration checks, drawdown and limitations.
Clean stone or geocellular soakaway crates?
Stone and crates provide different amounts of water storage within the same outside dimensions. The tool assumes 30% voids for clean stone and 95% for generic crates. Actual product data must be checked; selecting “specified product / custom voids” lets you enter a different void content.
Clean stone is selected first. If it cannot produce a passing automatic size, the calculator also checks geocellular crates. A crate solution can use less space for the same water volume, but it still needs adequate infiltration and suitable construction. Module dimensions, loading, cover, geotextile and installation details require their own review.
What should I check for a planning application?
Agree the drainage design basis with your architect or designer and the relevant local authority. Keep the infiltration report, proposed layout, levels, design calculations and arrangements for excess water together so the proposal can be assessed.
The optional garden screen assumes a clear rectangle and applies 5 m at the house, 3 m at the rear and 3 m at each side, plus the selected excavation allowance. These are limited screening assumptions. Confirm actual separation from structures, groundwater, adjoining and road boundaries, utilities and watercourses; the screen does not prove every clearance or site condition is acceptable.
The pack supports design review. It does not certify compliance with the full BRE Digest, establish site suitability or guarantee planning approval. A qualified designer must review the final arrangement and applicable requirements.
What does the €10 drawing and calculation pack include?
Sizing and dimension adjustments are free. The optional pack is a one-off €10 purchase and contains two A3 PDF sheets: an outline arrangement and the storm calculations with material allowances. It records the selected design and its assumptions for review.
The order flow provides private access to the purchased pack. Read the pack terms and scope before purchasing. The pack does not include carrying out an infiltration test, a site survey or structural certification.
Common soakaway questions
What if my soil drains too slowly?
Making the device larger may not resolve a failed drainage-time check. Review the test and site with your designer and consider a wider surface-water strategy. The calculator can return no suitable automatic size rather than approving an unsuitable option.
What if a soakaway will not fit in my garden?
Check both the device and excavation dimensions, the actual site boundaries and all relevant clearances. A rainwater planter may be worth assessing as part of another drainage arrangement. It needs its own sizing, outlet and overflow assessment; it is not an automatic solution for every site.
Can I use this for a septic tank soakaway?
No. This tool is limited to clean impermeable-roof runoff. Wastewater treatment and disposal require a separate site assessment and design.
Further reading
- BRE Digest 365: Soakaway design — the full publication is needed for final design review.
- Fingal County Council planning questions — includes soakaway design and setback guidance.
- South Dublin County Council water and drainage considerations — local submission guidance and related documents.
These are independent references and do not endorse this calculator.